2019-2020 Ducati Diavel 1260 Maintenance Schedule

The 2019-2020 Ducati Diavel 1260 maintenance schedule and service intervals — sourced from the owner’s manual.

This applies to these models:

2019 Ducati Diavel 1260
2020 Ducati Diavel 1260

Regular maintenance for the 2019-2020 Ducati Diavel 1260

This is maintenance that you can do yourself (though the manual says you need a dealer to do it).

Every 1000 km/600 miles miles OR 6 months (whichever comes earlier, perform the following maintenance:

Check engine oil level

Check brake and clutch fluid level

Check tyre pressure and wear

Check the drive chain tension and lubrication

Check brake pads. If necessary, contact your dealer to replace components

2019-2020 Ducati Diavel 1260 Maintenance Schedule Table

The following is the list of maintenance operations and to be done on this motorcycle with a distance or time interval — whichever comes earlier.

This maintenance schedule is in the same format as in the manual, though altered to fit this screen.

km. x1000	1	15	30	45	60	Time
mi. x1000	0.6	9	18	27	36	(months)
Reading of the error memory with DDS 2.0 and check of software version update on control units	•	•	•	•	•	12
Check the presence of any technical updates and recall campaigns	•	•	•	•	•	12
Change engine oil and filter	•	•	•	•	•	12
Clean the engine oil mesh filter assembly	•					–
Check and/or adjust valve clearance			•		•	–
Change timing belts			•		•	60
Change water pump belt			•		•	60
Change spark plugs			•		•	–
Clean plugs with metal mesh filters on heads					•	–
Clean air filter		•		•		12
Change air filter			•		•	–
Check brake and clutch fluid level	•	•	•	•	•	12
Change brake and clutch fluid						36
Check brake disk and pad wear. Change if necessary	•	•	•	•	•	12
Check the proper tightening of brake calliper bolts and brake disk flange screws	•	•	•	•	•	12
Check front and rear wheel nuts tightening	•	•	•	•	•	12
Check frame-to-engine fasteners tightening		•	•	•	•	–
Check wheel hub bearings			•		•	–
Check and lubricate the rear wheel shaft			•		•	–
Check the cush drive damper on rear sprocket			•		•	–
Check the proper tightening of final drive front and rear sprocket nuts	•	•	•	•	•	12
Check final drive (chain, front and rear sprocket) wear.		•	•	•	•	12
Check final drive chain tension and lubrication	•	•	•	•	•	12
Check steering bearings and lubricate, if necessary			•		•	–
Change front fork fluid				•		–
Visually check the front fork and rear shock absorber seals	•	•	•	•	•	12
Check the freedom of movement and tightening of the side and central stand (if any)	•	•	•	•	•	12
Visually check the fuel lines			•		•	–
Check rubbing points, clearance, freedom of movement and positioning of hoses and electric wiring in view	•	•	•	•	•	12
Lubricate the levers at the handlebar and pedal controls		•	•	•	•	12
Change coolant				•		48
Visually check the coolant level and sealing of the circuit	•	•	•	•	•	12
Check tyre pressure and wear	•	•	•	•	•	12
Check the battery charge level	•	•	•	•	•	12
Check the operation of all electric safety devices (side stand sensor, front and rear brake switches, engine kill switch, gear/neutral sensor)	•	•	•	•	•	12
Check lighting, turn indicators, horn and controls	•	•	•	•	•	12
Reset the Service indication through the DDS 2.0	•	•	•	•	•	–
Final test and road test of the motorcycle, testing safety devices (ex. ABS and DTC), Cruise Control device, electric fans and idling	•	•	•	•	•	12
Softly clean the motorcycle	•	•	•	•	•	12
Fill out that the service was performed in on-board documentation (Service Booklet)	•	•	•	•	•	12